Modern Classic SLR Series :
Canon EOS-1N AF SLR camera

File size: 63K HTML Loading...

eos1n2485mmsideA.jpg  
canon_logotrans.gif I am not happy with normal spec sheet I came across, so I thought I need to recreate another detailed page on my own. I have included system upgrades from previous EOS-1 to this page as quick reference source.

Full Technical Specifications of Canon EOS-1N AF-SLR camera

Where: improved Items changed from the previous Canon EOS 1. Tentative. stands for tentative value or tentative content

Note: -Content are solely based on full factory technical specifications for the camera. Compatibility with newer series of Canon EOS-1x series system accessories are not featured here. If there are any discrepancies on data and figures published herein this site, Canon official data should be the correct reference. Alternate way is to furnish me (via Message Board) with more information for updating any content in this site.

Credit:- "Canon", "EF", "USM" and other relevant logos, names and specialized technical terms are/could be registered trademarks of Canon Inc. Japan.

Type

  Type   Film-based 35mm vertical traveled focal plane shutter single-lens-reflex (SLR) camera with built-in motor drive.
  Format   24mm x 36mm
  Usable lenses   Canon EF lenses (for use with full-aperture metering but not stop-down metering.)
  Standard lens   Canon EF 50mm f/1.4 Tentative.
  Lens mount   Canon EF mount with electrical contacts

Auto-
Focus
("AF")

  Type:   TTL-CT-SIR system (TTL cross-type secondary image formation phase difference detection type usable to f/2.8 on the central vertical line)
  Focusing points:   I I + I I (Center: cross, lateral spacing 4.5 & 7.5 [mm]) improved
  Selection of focusing points:   (1) Manual selection of focusing points The photographer can select one of the five focusing points and lock in the selected point.
(2) Automatic selection of focusing points In one-shot AF mode: The subject information from the five focusing points is used to select the optimum focusing point, and focusing is carried out at that point. Predictive focus and Al servo AF mode: Although the central section is used at the start of focusing, Al servo AF operation continues even if the subject moves aside from the center sensor to a side sensor.
  Focusing modes   The following 3 modes are selectable
(1) One-shot AF mode. Once focused, AF operation stops -+ AF is locked at that position. Priority is given to the AF system: The shutter can not be released until AF is completed. When using evaluative metering, the AF and AE settings are locked, at the same time. (During partial or spot metering, metering is carried out in real-time until SW-2 ON.). CF-No.7-0: When using a USM lens, manual focusing by use of the electronic ring is possible immediately after completion of auto, focusing operation (after focusing is finished or when focusing is not possible). CF-No. 7-1: Cancels the function of the above 7-0.
(2) Moving object prediction Al servo AF mode The AF system keeps tracking the moving object until exposure is actually made. * The first frame after holding SW-I ON in stand by mode: Priority is given to shutter release and exposure can be made anytime regardless if AF is completed or not. * The first frame after quickly pressing SW-2 ON from SW-1 OFF: Exposure is made after AF control is completed once. The second frame and after during continuous. shooting- The lens is driven (driving time 0 - max. 250ms) in conformity with the necessity for object tracking before releasing the shutter. The in-focus mark does not light when the subject's focused, but blinks at 8Hz when focusing is impossible.
(3) Manual Focusing * AFD lens: Changeover from AF to Manual is made using the switch on the lens. * USM lens: Same as above (when CF-No. 7-1 is selected or automatic changeover (when CF-No.7-0 is selected. * When focusing is completed, the in-focus mark (a green LED) and superimposing lamp light. NO indication is given when the subject is not focused. * Manual focusing using the electronic focusing ring is not possible during continuous shooting.
  AF operation   CF-No. 4-0: Activated when the shutter button is depressed to the first step.
CF-No. 4-1: Activated when the, AE lock button is pressed ON. (* When CF-No. 4-1 is set, AE lock can be made by SW-1 ON.)
  AF operating speed   AF Speed is the same as the EOS-1
  Indication of AF focusing completion   By LCD indication in the viewfinder and by an electronic beeper sound. The beeper sound emitted when focusing is completed can be turned on or off (by the main switch).
CF-No.10-0: With superimposing display.improved
CF-No.10-1: Without superimposing display.improved
  AF auxiliary light   Provided when used together with an EOS flash unit (integrating an AF auxiliary light function). When a flash is used, near-infrared rays (peak wave length: 700nm) are automatically emitted from the flash whenever necessary. improved 540EZ: Auxiliary light corresponds to all five focusing points Other EOS flash units: Auxiliary light corresponds only to the central focusing point. An AF auxiliary light source is not built into the camera.
  AF working range   EV 0-18 (ISO 100) using Canon's standard test conditions
  Selection of the AF focusing point   CF-No. 11-0: Focusing point select button + main electronic dial.improved
CF-No. 11-1: Exposure compensation button + main electronic dial.improved
CF-No. 11-2: Exposure compensation button + main electronic dial. Or by operating the quick control dial (valid during metering, during metering timer operation or during continuous shooting operation only. Automatic selection is not valid.)improved
  Indication of the selected AF focusing point   Indication is made by a superimposed display in the viewfinder and by a 7-segment indicator in the external LCD.improved

View- finder

  Type   Eye-level type, single lens reflex viewfinder using a pentaprism. (Fixed pentaprism type with condenser lens.)
  Focusing screen   Interchangeable type. Full-surface laser-matte screen with fine spot metering area mark. (improved CII type) Standard equipment. Exchangeable from the mount section. (Interchangeable screens for the EOS-1 can also be installed).
  Standard diopter   -1 dpt, ± 2 dpt. Built-in dioptric adjustment function (eyepoint: 20mm). Rotation angle of the dioptric adjustment knob: 360° Clicks at every 18°.
  Viewfinder coverage   Virtually 100% both horizontally and vertically. (99% 1%)
  Magnification   x 0.72 (-1 dpt, 50mm lens at oo)
  Viewfinder information   (A) Central section of the viewing area
(1) AF frames (displayed by the SI screen, not by the focusing screen).
(2) Fine spot metering area mark (in the central section only)
(B) Bottom of viewfinder with LCD (yellow-green LED backlight) indications of values, patterns and letters.
* Shutter speed (Out-of-coupling-range warning: Blinks at 2 Hz);
* Aperture (Out-of-coupling-range warning: Blinks at 2 Hz)
* CF-No.6-0: Fully digital value indications in 1/3-stop increments.
* CF-No.6-1: Fully digital value indications in one-stop steps.
* CF-No.6-2: Fully digital value indications in 1/2-stop increments.improved
      Depth-of -field AE mode , Focusing point: The central focusing point in case of automatic selection and t ' he manually selected focusing point in case of the manual selection.
      :- AE lock (During AEB shooting: Blinks at 2Hz)
      M:- Manual
      :- Flash charging completed
      :- Exposure compensation (Also lights. during flash exposure compensation.improved) (Also lights during flash exposure compensation using the 540EZ or 430EZ.)
      :- AF focusing completed (when NG: Blinks at 8Hz)
  Outside the visual field, to the.right   LCD (yellow-green LED backlight) indications of scales, dots and symbols.improved
      1/3-stop scale ±3 stops)
      Dot bars symbols &
AE mode: Exposure compensation amount
AE lock: Real-4ime metering deviations
Manual exposure level
Background exposure values during flash photography. (Results of in-body metering)
      -6 Flash exposure (body setting or when setting the 540EZ or 430EZ) improved
      Remaining frame display (Digital indication using "" plus figures I - 9.) These indications cannot be canceled With built-in illumination for the LCD information window (Green LED backlight).
  Mirror   Quick-return type. Full-surface half-mirror (Reflection: Transmission = 63:37, EOS-1 series only.)
      Viewfinder blackout time: 140ms -or less at shutter speeds of 1/60 sec. or faster)
      Operation:- CF-No. 12-1: Enables mirror-up exposures. SW-2 ON brings up the mirror, then SWA OFF and SW-2 ON release the shutter.improved The 'mirror up operation timer keeps the mirror up for a maximum of 30 seconds. (After 30 seconds.- the mirror comes down and exposure interrupted)
      Mirror blockage. Does not occur with lenses up to the 1,200mm f/5-6
      Depth-of-field check. Possible (one-touch, activation -of the -dedicated button stops -the lens down to the calculated aperture valve).
      Eyepiece shutter. Provided. Exclusive eyecup Ec-II with locking feature is provided as standard equipment (removable). An angle finder, magnifier or diopter compensation lens E can be attachable to the eyepiece.
       
The Day after .. Tsunami 2004
Contact Andy Eames

The day after .. Tsunami, Asian Crises.


Credit: Image courtesy of Andy Eames ® who has his Portfolio at Pbase. Image copyright © 2005. All rights reserved. Please respect the visual property of the contributing photographer.

Exposure control

  Metering   TTL full-aperture metering using a sixteen-zone SPC and BASIS. Selectable from the following three methods:
(1) CF-No.8-0: Evaluative metering CF-No.8-1: Center-weighted average metering.
(2) Partial metering (Metering range: Central A0, A1, A2 and B5, corresponding to about 9.0% of the viewfinder area).
(3) Fine spot metering (about 2.3% of the viewfinder area). CF-No.13-1: improved Spot metering linked with the focusing points. (Using A0 - A4, about 3.5% of the viewfinder area. A0 is used in automatic focusing point selection mode.) Note:- The first frame when making continuous exposures:- Real-time metering. The second frame and after:- AE locked exposures same as the first frame.
      Metering range:-
(1) Evaluative metering: EV 0 - 20 (at normal temperature, 50mm f/1.4 ISO 100)
(2) Partial metering: EV 0 - 26 (same conditions as above).
(3) Fine spot metering: EV 3-20 (same conditions as above).
Out-of-coupling-range warning External and viewfinder internal LCD digital display blinks at 2 Hz.
  Auto Exposure Modes   Selectable from the following SIX (6) AE modes or for manual exposure control.
(1) Shutter-priority AE (without the safety shift function).
(2) Aperture-priority AE (same as above).
(3) Depth-of-Field AE (shifting not possible: the depth is measured with the central focusing point in automatic focusing point selection mode, and the manually selected focusing point in manual focusing point selection mode).
(4) intelligent ~ program AE- (shifting possible) -
(5) A-TTL program flash AE (3-point flash exposure metering improved)
(6) TTL program flash AE (3-point flash exposure metering improved)
(7) Manual (bar dot display, metered manual) CF-No.5-0 Tv set: Electronic dial. AV set: Quick control dial. CF-No.5-1 Tv set: Electronic dial. Av set: Quick control dial Note: -When the E1 Command Back is attached: Since. the quick control dial is not available, its function is substituted by the "exposure compensation button ON + main electronic dial operation".
  Bulb   CF-No.6-0: The setting pitch of Shutter Priority AE, Aperture Priority AE and Manual is in 1/3stop increments.
CF-No.6-1: The setting pitch of Shutter Priority AE, Aperture Priority AE and Manual is in f-stop increments.
CF-No.6-2: The setting pitch of Shutter Priority AE, Aperture Priority AE and Manual is in 1/2stop increments.
  Exposure reading   Works when the shutter button is depressed to the first step.
Before release: The metering timer works for 6 seconds after the finger is removed from the shutter button.
After release: The metering timer works for 2 seconds after the finger. is removed from the shutter button.
  Film~speed range   CF-No.3-0: ISO 6 - 6400 ISO 25 - 5000 are for automatically set in 1/3-stop steps according to the DX code. Manual setting can also be made. When NON-DX code film is used, the previously set ISO film speed blinks in the display -+ manual setting is required. CF-No.3-1: Manual setting only (ISO 6 - 6400)
  Exposure compensation   (A) AEB: Auto exposure bracketing
a) Presetting Possible in all exposure modes excluding (3), (~) and (6) of the AE modes listed above in 4-2.
b) Operation Press the battery check button + the film winding mode select button and turn the main electronic dial. CF-No.9-1, -3: Can also be set by holding the AF mode select button + shooting mode select button pressed ON and turning the main electronic dial.
c) Bracketing range CF-No.6-0, -1: 1/3-stop steps ± 3 stops improved CF-No.6-2: 1/2-stop steps ± 3 stops
d) Number of exposures Three frames are exposed in accordance with the film transport mode as given below:
CF-No.9.-0, -1: 3 frames in the order of - - 0 - +
CF-No.9-2, -3: 3 frames in the order of 0 - - - + improved
      e) The affected camera setting(s) for the various shooting modes are as follows:
Exposure control modes

Tv

Av

Shutter-priority AE

-

Aperture-priority AE

-

Depth-of-field AE

-

Program AE

Manual exposure CF-No.5-0

-

CF-No.5-1

-


) Cancellation CF-No.9-0, -2: CLEAR, flash charge completion, bulb, main switch "L", lens exchange, film loading, AL or REW. improved CF-No.9-1, -3: AEB operation is canceled when one of the following occurs: CLEAR, flash charge completion and bulb.
      fB) Manual setting
1) Range and precision
CF-No.6-0, -1: 1/3-stop steps ± 3 stops
CF-No. 6-2: 1/2-stop steps ± 3 stops improved
2) Operation
CF-No.11-0: Quick control dial, exposure compensation button + main electronic dial.
CF-No.11-1: Quick control dial, focusing point select button + main electronic dial. improved
CF-No. 11-2: Focusing point select button + main electronic dial improved
(3) Combinations of the above (1) and (2) are also valid.
  AE (Auto Exposure) lock   (1) Auto AE lock The AE reading is locked at the instant focusing is completed in one-shot AF mode when using evaluative metering.
(2) Manual AE lock CF-No.4-0: Effective in any metering mode by pressing the AE lock button.; CF-No.4-1: Effective in any metering mode by pressing SW-1 ON. When the metering timer is working, AE lock is maintained and can be renewed by pressing the shutter button again.
To cancel, wait for the metering timer to go OFF, turn the main SW to "L", or press one of the respective mode buttons, BC, CLEAR, REW or CF button. The AE lock button does not function while an EZ series flash is being used after charging is completed.
  Multiple exposures   Possible. Automatic returning continuous multiple exposures are possible. (Film drift: 0. 1 mm. or less) Designation of the nuffiber of multiple exposures is also possible (up to 9 exposures, maxi). (Intermediate cancellation or resetting is also possible.)

Shutter

  Type   Focal plane type, all speeds electronically controlled, using vertical-travel carbon blades. Electromagnetic- control independently releases the first curtain and second curtain, respectively. (Curtain speed 2.7 ms/24mm)
  Shutter speed range   1/8000 sec. ~ 30 sec. 1/3-stop digital indications on the LCD; X = 1/250 sec.
In shutter-priority AE and manual exposure modes.
CF-No.6-0: 1/3-stop settings possible.
CF-No.6-1: 1-stop settings possible.
CF-No. 6-2: 1/2-stop settings possible.improved
Elapsed time indication is provided in bulb mode. (Advances 3 bar marks every 30 seconds, indicates up to 120 seconds.)
  Shutter release system   Soft touch electromagnetic release system (without cable release socket)
  Release time lag   (1) Time required from SW-2 ON until start of exposure, after holding SW-1 ON -64ms
(2) Time required from simultaneous pressing of SW-1 and SW-2 until start of exposure -200ms
  Self-timer   Electronically controlled, timing selectable between 10 sec. and 2 sec.
  Camera-shake warning   improved The self-timer starts when AF operation is finished in any AF mode (the AE reading is locked at this time) and, also, when the shutter button is pressed to the second step. ("AND" activation) (The timer will not start even if the shutter button is pressed until the AF operation is finished.) The self-timer operation is indicated by an LED (Initial 8 sec.: 2Hz, final 2 seconds: 8Hz flashing) and the external LCD counts down the seconds with a digital display. To cancel the timer after activation, set the main switch to the "L" position and timer operation will be interrupted.

Film
transport

  Film loading   Automatic loading using a sprocket and toothed spool. Blank film advance starts automatically when the back cover is closed after loading the film roll (only the film advance mechanism operates) and winds the film until the film counter reaches 'T' (time required: 3 sec.) before stopping automatically. * AL is not possible when the main SW is at "L".
  Winding system   (1) EOS-1N alone: Continuous exposure (C) mode or single exposure (S) mode.
(2) EOS-1N + type AA BP-1: Continuous exposure (C) mode or single exposure (S) mode.improved
(3) EOS 880 + PDB-E1 High-speed continuous exposure (C
H) mode, low-speed continuous exposure (CL) mode or single exposure (S) mode.
  Start of film winding   Film winding starts when the exposure completion signal is detected.
  Film winding check   By bar mark floating (--->>>) on the LCD display panel.
  Winding speed
[frames/sec]
  (1) Continuous exposure: As shown in the table below, using a Tv of 1/250 sec or faster.
  One-shot/Manual AI servo AF Remarks

CH

Approx. 6 Approx. 5 EOS-1N + PDB-E1 Power source: LR6 x 8
EOS-1N + PDB-E1 Power source: FR6 x 8

CL

Approx. 3 Approx. 2.5

C

Approx. 3 Approx. 2 EOS-1N alone Power source: 2CR5 x 1
EOS-1N + AA-size BP-E1 Power source: LR6 x 4

(2) Single exposure: Single frame advance at speed equivalent to C -mode when EOS-1N is -used alone, or CH mode when used with the PDB-E1
  Shooting capacity
Number of 24 exp. x 36 exp. film rolls
 

Conditions

EOS-1N alone

EOS-1N + Type AA BP

EOS-1N + PDB-E1

Power source

2CR5 x 1

2CR5 x 1

LR6 x 4

LR6 x 8

KR15/51

Normal
temperature
(+20
°C)

75/(50)

75/(50)

45/(30)

100/(65)

45/(30)

Low
temperature
(-20
°C)

12/(8)

12/(8)

0

6/(4)

30/(20)

  Film rewinding system   Automatic rewinding by means of a coreless miniature motor.
  Start of rewinding   (1) Automatic CF-No. 14, -2: Auto-Rewind starts under the following conditions (-0 high speed and Tentative. -2 silent)
a) When the DX designated number of exposures are completed.
b) When the film end is sensed (by tension). CF-No.1-1, -3: Automatic rewinding starts when the film rewind button is pressed after the film roll is completed. (-1 high speed and Tentative. -3 silent)
(2) Mid-roll rewind Mid-roll rewinding is possible at all times by pressing the film rewind button.
  Rewinding confirmation   By bar mark floating and countdown of the frame counter display.
  Rewinding time (Sec.)   Time required for rewinding a 24exp/(36exp.) roll, using new batteries and under normal temperature

Conditions

EOS-1N alone

EOS-1N + Type AA BP

EOS-1N + PDB-E1

Power source

2CR5 x 1

2CR5 x 1

LR6 x 4

LR6 x 8

KR15/51

CF-No.1

0.1

about 5/(8)

about 5/(8)

about 5/(8)

about 5/(8)

about 5/(8)

2.3

about 13/(20)

about 13/(20)

about 13/(20)

about 13/(20)

about 13/(20)

  Rewind completion   CF-No.2-0: Stops automatically after the film leader is wound completely into the cartridge.
CF-No.2-1: Stops automatically leaving just the film leader section protruding from the cartridge.
Under CF-No.2-1, when the shutter is released with the back cover open, the shutter is activated at Tv=1/8000 regardless of the condition. (For protection of the shutter mechanism.)
  Rewinding completion indication   Cartridge symbol blinks at 2Hz in LCD panel.
  Film existence check   (1) Always indicated by a film cartridge symbol on the LCD display panel.
(2) By visual check using the back cover's film check window.
  Frame counter   (1) Forward sequence (reverse sequence during rewinding) digital indication by the electronic counter on the LCD panel. (2) Countdown film remainder indication via 7-segment LCD numbers (I digit) in the viewfinder. 36 - 10: F 9 -1: Digital indication as is. (The display disappears during rewinding)
  Film rewinding sound   48dB at 15 cm behind the camera.

Camera
body

  Back cover   Can be opened or removed by operation of the back cover open latch (with safety lock mechanism). Provided with a film existence check window (without a memo-holder).
       
  Flash contacts   (1) At the accessory shoe: X - Direct connection contacts
(2) At the lower section of the right side of the camera body: JIS type-B socket (with lock screw and shock prevention function provided on the accessory shoe side). Simultaneous use of (1) and (2) contacts for simultaneous flash firing is also possible.
  Accessory shoe   Provided. Equipped with a lock pin hole to secure the flash unit.
  Automatic flash   Using EOS type EZ series flash units with the camera set to program AE mode.
(1) A-TTL flash exposure The shutter speed is automatically set to a synchronizing speed (1/250 - 1/60 sec.) when charging is complete and the optimum flash aperture value is automatically set in compliance with the shooting determined by pre-emission of near infrared light and the subject conditions (brightness) by the A-TTL
  Flash exposure compensation   (1) Number of stops CF-No.6-0, -1: 1/3-stop steps ± 3 stops. CF-No.6-2: 1/2-stop steps 3 stops
(2) Operation Metering mode button + quick control dial or Metering mode button + focusing point select button + main electronic dial.
  Custom functions   14 custom functions available. (M Refer to Custom Function/Settings section for a list of these functions).
improved Preset CF-No. is displayed on the external LCD panel (exposure bar indicator).
  Clear button   (1) When this button is pressed under normal state, respective items -are simultaneously reset to the following status.

No. Item

 

Reset status
1. Shooting mode

 

Program AE
2. AF mode

 

One-shot AF
3. Metering mode

 

Evaluative metering
4. Film rewinding mode

 

S (single exposure)
5. Preset multiple exposures,

 

Total cancellation / initial status
6. Exposure compensation

 

7. AE lock

 

8.AEB

 

Canceled

However, when using partial metering, fine spot metering or spot metering, under the CF-No.8-1 (whereby the evaluative metering mode is changed to center-weighted average metering mode), the metering mode is not changed even if the clear button is pressed ON.
(2) When the clear button is pressed in the custom function setting state, all the custom functions are automatically reset to their home positions (-0).
  Power source   (1) One 2CR5 lithium battery: 6V Housed inside the grip.
(2) When attaching the PDB-El, remove the grip from the body and supply power to the camera body from the PDB-El power source (LR6 x 8: 12V).
(3) When the type AA battery pack BP-E1 is attached, either of the 2CR5 lithium battery at 6V inside the grip or the LR6 x 4 at 6V in the battery magazine can be used to supply power to the camera body.improved
  Main switch   Turns the camera OFF when set to the "L" position.
  Battery check   3-step bar mark display (4-step display including OFF indication) is made on the LCD panel when the BC button is pressed.
  External display   Large-sized LCD panel. Built-in full-surface uniform illumination (EQ function.
  Tripod socket   CU-1/4
  Remote control   Possible. A three-pin remote control socket is provided in the lower section of the left side of the body
  Grip exchange   Possible. (When replacing the battery or when attaching the PDB-E1 or type AA BP-E1)
  Body material   Diecast aluminum (body aperture section) and glass-fiber reinforced poly-carbonate resin. External color finish: Black
  Dimensions   161(W) x 112.1(H) improved x 71.8(D) mm / 6-5/16(W) x 4-7/16(H) x 2-13/16(D) in. (body thickness: 55.8 mm 2-3/16 in.)
  Weight   855 grammes / 29.925 oz (excluding lithium battery. + 40 g/ 1.4 oz including the battery.)

System Accessories

      Battery pack BP-E1 (also usable with the EOS-1).
540EZ (clip-on type system flash usable with an e external power supply).
Wireless controller LC-3 (three terminal remote controller for EOS series cameras).
Eyecup Ec-II (standard equipment with the EOS-1N/EOSEOS-1N RS and also attachable to the EOS-1).
Focusing screen Ec-ll (standard equipment with the EOS-1N/EOS EOS-1N RS).
Semi-hard case (Two types -L and LL- are available. Also usable with the EOS-1.)

| Questions, Issues & Answers | Canon EOS-1 Series Message Board
| Canon EF lens Board | in a shared environment
| Free Trade Zone | shared environment

| Back | Index Page The Canon EOS-1N Series Professional SLR camera
| Back | Main Index Page The Canon EOS-1 Series Professional SLR camera

Background and Various Issues | The Basic Features & various Setup
Manual & Auto Focusing | Metering Systems | Exposure Control | Viewfinder Optical
System
Flash Photography (with Speedlite 540EZ extension & Selective info on Canon TTL Flash Models:-160E | 200E | 300EZ | 300TL | 420EZ | 430 EZ | 480EG | MacroLites | Other non-TTL Canon flash model

Reliability Issues:- Body Chassis | Shutter Unit | Electronic Circuitry | Film Transport & film handling Secondary Functions:- Custom Function Part One | Part Two | System Accessories:- Film Back Options - instruction for Command Back E1 | Macro/Close Up Part one | Part two and Part III Flash for Macro-Photography | Power Sources -BP-E1 | PDB-E1 | Focusing Screens | Remote Control with Wireless Remote Set LC-3 | System compatibility

Variants of Canon EOS-1N:- Canon EOS-1N RS | Canon/Kodak Digital DCS-1, 3 -5 & 520/560 Series | Full Technical Specification | Main Reference Map / Nomenclature | Resource Centre:- Comparative Charts between EOS-1 & EOS-1N / or with its active Competition(s) (Nikon); Quick Operational Reference Card (278k Gif File); Listings of 7-segment digital numbers/letters appeared on LCD display panel/viewfinders (HTML page); External Link:-Instruction Manual (3.3MB PDF file applicable for both Canon EOS-1N (RS). | Using EOS system for your photography | Bots & Nuts of EOS System - by Philip Chong |

The Eyes of EOS -
EF Lenses
A little OFF-TOPIC SOME Personal Thought

MIR Logo
HOME - Photography in Malaysia
Search.gif

Developer Link

Volunteered Maintainer(s) for the Canon EOS-1N Series Message Board: Philip Chong, Editor, Digital Camera Magazine; Vincent Thian, Photo Editor, Malaysian Bureau, Associated Press "AP", CYleow, Ex-photo Editor of local daily, The Star; Gary Rowan Higgins, Australia and other nice folks on the web.

Special Credit:- :Mr. Richard Yeow & Mr. Simon Wong from camera division of Canon Malaysia Logo Marketing Malaysia, for their continual effort in supporting development of this EOS/EF website. Others: All the nice people on earth who have contributed their photos and pictures of personal works or product shots for the creation of this site. Certain content and images appeared in this site were either scanned from official marketing leaflets, brochures published by Nikon and/or contribution from surfers who claimed originality of their own work for public publishing in this website, where majority of the extracted information are used basing on educational merits. The creator of this site will not be responsible for any discrepancies that may arise from any possible dispute except rectifying them after verification from respective source. Neither Nikon or its associates has granted any permission(s) in using their public information nor has any interest in the creation of this site. "Canon", "EOS", "EF" "RT", "EOS-1n RS", "Booster ", "Macrolite", "fluorite", "Image Stabilizer" & other applicable technical/business terms are registered trade name(s) of Canon Inc., Japan. Site made with an Apple G5 IMac.